Re: Request ScreenOS 6.3.0r3 for ISG1000
Dear. Thanks for your reply. Problem is that in link: https://www.juniper.net/support/downloads/?p=isg1000#docs is the release notes of 6.3.0r3 version but not OS version, only is from 6.3.0r12. Regards.
View ArticleRe: Request ScreenOS 6.3.0r3 for ISG1000
Hello, Indeed that is the case. I think you will need to open the JTAC case to get these older OS releases. Regards, Rushi
View ArticleRe: Misleading logging on ScreenOS ISG1000 FW
Hello, There were some cosmetic issues reported previously. In your case, is the issue still seen when you use the command line interface? What OS version are you running on the device ? RegardsVatsa
View ArticleRe: NetScreen 5400 problem
Hello, What are the IO modules connected to the device? Can you try removing all IO modules and having only MGT card and boot the device. If the issue goes away, it can be a issue with one of the IO...
View ArticleRe: cannot download config file from GUI after upgrade
Hello, Configuration was be optimized as follows :- 1. review config for unsed services, address objects, certificates, policies, VPN and any other settings and delete them if they are not needed.2....
View ArticleRe: can't fetch reports for netscreen firewall
Hello, A easier way to check this would be to check the snmp counters under get snmp to see if there are out packets increasing on the device or not. You can also do a debug for snmp "debug snmp all"...
View ArticleRe: Transparent mode segmentation on SSG20 ?
This would also be a good introduction for the SRX http://forums.juniper.net/t5/Day-One-Books/Day-One-Book-Deploying-SRX-Series-Services-Gateways/ba-p/52398
View ArticleRe: SSG5 Bandwith problems
Find this policy on the list of the web UI. Edit the policy go to the advanced tabUncheck the box for Traffic Shaping and save
View ArticleRe: Request ScreenOS 6.3.0r3 for ISG1000
For versions that are no longer listed on the public site you need to open a ticket with JTAC for a custom download link.
View ArticleNS 5GT Bricked...Boot Loop
I have an old netscreen 5GT when i connect console i am getting the below message,Not able to factory reset alsonot able to run any command also.when i try to restore any firmware via tftptftp is...
View ArticleRe: NS 5GT Bricked...Boot Loop
Hello, Which tftp server you are using & which port on the NS5GT is connected to tftp server?Also is tftp server directly connected to NS5GT? Following error indicates that authentication-key on...
View Article[SSG 520M] Issue with bootloader upgrade
Hi, I try to upgrade the bootloader because of the message:********Invalid DSA signature********Bogus image - not authenticated but when i finished to fill the different fields i optain this new...
View ArticleRe: [SSG 520M] Issue with bootloader upgrade
Hello , This looks like issue in either cable or the interfaces. Usually the firewall will try to get the interface up so that the TFTP communication can go through. In your case, since you have tried...
View ArticleRe: SSG5 Bandwith problems
Hello , The policy you have shown is from untrust to trust.. There should also be another policy that is from inside trust to untrust that might have the policy bandwidth configured. RegardsVatsa
View ArticleRe: NS 5GT Bricked...Boot Loop
Yeah initially i was using some small tftp server.But read somewhere Solarwind TFTP server is better compared to others.downloaded and tried that initially it was the same.Timeout.Then i manually...
View ArticleRe: [SSG 520M] Issue with bootloader upgrade
This error will occur if you upgrade to the new ScreenOS image and still have the OLD signing key on your device. The boot screen on the console port will show this message:********Invalid...
View ArticleRe: [SSG 520M] Issue with bootloader upgrade
Hi Steve, As you can see, the vox is already stuck in the bootup. So, user cannot delete the imag key anymore. The only option is to re-image the box with an old firmware, get into the box management...
View ArticleRe: [SSG 520M] Issue with bootloader upgrade
Hi, On a healthy device, the output should look like: Saipan motherboard proto 3 or later detectedProbing...[Ethernet0/0 and Ethernet0/1]Initiating hardware and waiting for link up ...self_ip =...
View ArticleSSG140 cross-subnet problems
Greetings. I have a pair of SSG140 firewalls set up in NSRP (Yes, I know they're old). I have two subnets on the same virtual router and in the same zone (192.168.42.0/24 and 172.20.0.0/16) which are...
View ArticleRe: SSG140 cross-subnet problems
Sounds like a possible session timeout issue. Run a debug flow basic to make sure that the traffic is flowing correctly.
View Article