Re: unable to access DVR through ssg5
I don't have a version to check to see if the menu options have changed from 6.2 to 6.3. Do you have access to downloads to upgrade? If not can we explore the menus looking for where custom...
View ArticleRe: Route traffic through VPN tunnel
There are a few elements to having this fully working so I will separate them out. --AWS route from your routerThis you appear to have covered by sending the 10/16 network over to the SSG5 that has the...
View ArticleRe: unable to access DVR through ssg5
here is the current config still not able to see the cameras not aware of how to get latet version of the softwarethanks Michaelunset key protection enableset clock ntpset clock timezone -6set...
View ArticleRe: unable to access DVR through ssg5
Hi,In new config, I see below :set interface ethernet0/0 vip interface-ipIt doesn't have any reference of port/service etc.Looks like a new service Cameras has been created to replace old "camera" ....
View ArticleVPN Client Tunnel all traffic option does not work
Hello,I have a SSG5 and created VPN connection for the clients, with Shrew Soft client. Followed several tutorials and this one:https://www.shrew.net/support/Howto_Juniper_SSGNow I have a vpn working...
View ArticleRe: unable to access DVR through ssg5
still with Issues. Is there a good reference to working with the OS on SSG5? here is the new configunset key protection enableset clock ntpset clock timezone -6set vrouter trust-vr sharableset vrouter...
View ArticleRe: unable to access DVR through ssg5
Is your camera access still not working ? How are you accessing the camera ? Any webpage etc, IP/port number ?Please configure and enable the debug flow basic as in the document :...
View ArticleRe: unable to access DVR through ssg5
camera access still not working from the public ip can see it fine on either end of the tunnel. Using idmss lite to test trying to reach the cameras on http://72.24.30.166 port 3777 which is...
View ArticleRe: unable to access DVR through ssg5
Looking at your configuration it seems you have a typo in the port number for the VIP forwarding. set interface ethernet0/0 vip interface-ip 37777 "Cameras" 192.168.1.89 37777 instead of 3777
View ArticleRe: VPN Client Tunnel all traffic option does not work
When you want all traffic via the tunnel you will also need to change this setting on the SSG side for the destination address to be everything 0.0.0.0/0 instead of your limited resource address...
View ArticleRe: VPN Client Tunnel all traffic option does not work
Thank you very much for the answer.Before I test this solitions a few questions:1. Does 10.1.2.0/24 mean 0. 0, 0. 0/0???2. As for IP range, my internal network is /24 network. When connected wit vpn,...
View ArticleRe: VPN Client Tunnel all traffic option does not work
Hi, You can enable NAT under the 'Advacned' section of your policy.Also, 'tunnel all' from a VPN client gets complicated wit a policy based VPN. I would suggest using a route based VPN...
View ArticleRe: VPN Client Tunnel all traffic option does not work
Sorry for the confusion. What I copied there is the specific step in the instructions you link to that you need to change to have the tunnel setup for all the traffic to go to the SSG instead of split...
View ArticleRe: VPN Client Tunnel all traffic option does not work
Thank you for your patience.Making progress.ad. 1. I corrected my policy according to your advice. So now the configuration is:Untrust to TrustName = vpnclient_inboundSource AddressAddress Book Entry =...
View ArticleRe: VPN Client Tunnel all traffic option does not work
For the ip address pool you are entering a range of addresses. These addresses are used on the client at connect time and will be the source address of those internet requests that are not currently...
View ArticleRe: VPN Client Tunnel all traffic option does not work
That is exactly what I did. I created an address with the whole range actually of the adresses from my pool.Created a policy. Enabled NAT. Still nothing.To clarify: my pool for the vpn is...
View ArticleRe: VPN Client Tunnel all traffic option does not work
The zone for the pool addresses will be the same zone used for the local side of your VPN policy where you changed the address to 0.0.0.0/0. The internet side is usually called untrust. To clarify: my...
View ArticleRe: VPN Client Tunnel all traffic option does not work
What would it be then for 192.168.11.50-192.168.11.55?Also 192.168.11.48/29?
View ArticleRe: VPN Client Tunnel all traffic option does not work
Yes that is correct. You can google subnet calculator to find only where the boundaries are for any particular range of addresses.
View ArticleRe: VPN Client Tunnel all traffic option does not work
Then it still does not work. Only local network is available.
View Article