Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
Hello, I bought SSG5 (second hand)I haven't credentials and the console is disabled. I need bootloader version 1.3.2 or 1.3.3 (with old signing key) to erase completely this devide and load again a...
View ArticleRe: Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
Loading a new bootloader will not do anything for this. You would need to reset the device back to factory default settings via the pinhole (hopefully it is not disabled as well)....
View ArticleRe: Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
Hello, If you do not have credentials, try to reset the password which reset firewall to factory default....
View ArticleRe: Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
I follow the guide to reset factory by press reset button, but doesn't appears. Maybe the reset button is also disabled.Other solution ? Are you sur if I load new bootloader that dosen't change...
View ArticleRe: Basic BGP Configuration
You can place these two interfaces into the same zone and have both work with the /28 from your ISP. You will need this routed to both interfaces or you will need to use the BGP to adverstise the...
View ArticleRe: SSG140 failed during upgrade
Hi Vikas, I will try later and thank you so much for your kind help. thanks.
View ArticleRe: Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
If console is disabled, pinhold reset button also and if I haven't the credential, How I can reset this equipement ?A magic code or a magic guide to explain this ?
View ArticleRe: Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
Hello, You can try to get login prompt through SSH or telnet or webgui.If you are successful, use Serial Number of the device as username & password. This will reset the configuration to factory...
View ArticleVPN connectivity going up and down intermittently between ISG 1000 and SSG350M
we have SSG-350M and ISG1000 at one site. The VPN tunnel was up till the time we reloaded our core switches as some routing was changed and everything was disrupted.I have cleared the sa and...
View ArticleRe: VPN connectivity going up and down intermittently between ISG 1000 and...
Hello, On SSG350M, the state of 'get sa' output is A/D which is Active/Down. So on SSG350, Phase 2 is down.From ISG logs, it looks like on ISG phase 2 is complete, but SSG350M does not bring Phase 2 up...
View ArticleRe: VPN connectivity going up and down intermittently between ISG 1000 and...
A/D indicates that VPN monitoring is failing. If you disable VPN monitoring, does the VPN remain up? The "D" means that VPN monitoring is not receiving a response, so it is assuming the VPN is down.
View ArticleRe: Bootloader 1.3.2 or 1.3.3 for SSG-5 needed
Serial number reset only works via direct console. Looks like you are going to need to RMA the device.
View ArticleHello Juniper I have a question. I want to know how you can download the...
Good morning . juniperHave a nice day todayI am a network engineer in KoreaI want to know how to get the Screen OS Download I want to receive permission to download I really want to know how to get...
View ArticleRe: Hello Juniper I have a question. I want to know how you can download the...
1: first you should have access to www.juniper.net. Check below:https://kb.juniper.net/InfoCenter/index?page=content&id=KB9946&actp=search 2: Once you have access to the support site then you...
View Articlessg140 - bgroup interface with different settings?
hello guys,can i put in a bgroup 2 interface with different physical settings?I need to have a port at 100mbps and one other at 10mbps...if i try this config could i have problem?thx in advancebye
View ArticleRe: ssg140 - bgroup interface with different settings?
Hello, bgroups on SSG140s are only supported on Univrsal PIMs in addition to built in ports.So if you utilize inbuilt ports on SSG140 for bgroup1, you can utilize ports on another Universal PIM for...
View ArticleRe: ssg140 - bgroup interface with different settings?
Hello Rushi,thanks for response.There's any chance to put different settings for ports in the same bgroup?Andrea
View ArticleRe: ssg140 - bgroup interface with different settings?
Hello, I just checked in the lab that once you put the interface in bgroup, you can not change the bandwidth of assigned interface.Only bgroup related bandwidth can be changed. e.g. if I put eth0/4...
View ArticleClik here to view.
Re: ssg140 - bgroup interface with different settings?
Cool Rushi,really thanks i appreciate your help!bye
View ArticleRe: Basic BGP Configuration
Thanks. Would it be possible to use a loopback interface and have both WAN links as part of the loopback group. Then configure the MIP on the loopback interface? As it stands the carriers states they...
View Article