In SSG, can I have MIP and VIP in the same external IP and different internal...
Hi everyone, I have a SSG with a MIP (for example 1.1.1.1 to 192.168.0.20), but I also want to configure a VIP in the same external IP for a different internal IP (1.1.1.1 to 192.168.0.100), and this...
View ArticleRe: In SSG, can I have MIP and VIP in the same external IP and different...
You cannot use a MIP and VIP with the same IP address. When you try to configure the second one it will tell you that the address is already in use.
View ArticleSSG5 debug proving to the cisco guy that the issue is...
I have a situation where an ssg5 is connected to the lan bg0 10.10.10.10/24 and on BG1 10.10.30.0/24 is a VoIP system. (The data is cisco and voice is juniper) I manage the VoIP network which is...
View ArticleRe: SSG5 debug proving to the cisco guy that the issue is...
Sounds as though they do not have a route to the 10.10.30 network. If a traceroute just times out, then it sounds like you aren't even getting through the first hop.
View ArticleRe: SSG5 debug proving to the cisco guy that the issue is...
Thanks. that's what I was thinking. Strangly when you tracert to the 10.10.10.10 address that i can ping to i get only one hop directl to the 10.10.10.10 ip. I really wnat to be 100% sure because this...
View ArticleRe: Basic BGP Configuration
Ok thanks. I kinda realized what I posted wasn't right shortly after I posted. I think i understand how it needs to be configured, but still have an issue in terms of how I'd finalize some of the...
View ArticleRe: SSG5 debug proving to the cisco guy that the issue is...
Is there any other test that you can think of that could be done to be 100% certain?
View ArticleRe: In SSG, can I have MIP and VIP in the same external IP and different...
Emendez, Please check the below KB, I think it's doable: https://kb.juniper.net/InfoCenter/index?page=content&id=KB26612&actp=search Thanks,Vikas
View ArticleRe: SSG5 debug proving to the cisco guy that the issue is...
1: If sender doesn't have route to 10.10.30.0/24 subnet then nothing much that you can do. Probably, you can check you debug filters" get ff" to make sure your filters are correct. 2: You can do the...
View ArticleSSG140 failed during upgrade
Hi all, I have perfomed software upgrade but stuck after upgrade imagekey.cer.Only POWER led is green, others are OFF and I get this message when console the router: Self IP Address [10.10.10.13]:TFTP...
View ArticleRe: SSG140 failed during upgrade
I hope you have new image and imagekey.cer downloaded from the website, not any old downloaded software. 1: Reboot only after upgrading the imagekey.cer. and then image and then reboot. updating the...
View ArticleRe: SSG140 failed during upgrade
Hi Vikas, Thanks for quick reply.Juniper SSG140, I forgot what was the last OS version.My last attempt of upgrade was last year I think, and when stuck I just leave it there.Now I need this router to...
View ArticleRe: SSG140 failed during upgrade
Ok so, it rebooted after upgrading the imageket.cer and without upgrading the image file. Then, It's expected as the old software was signed by old skey and device it's unable to validate the old...
View ArticleRe: SSG140 failed during upgrade
thanks for your quick reply.I've tried many times actually but I get the same error.. "invalid image" Loading system image "$BABOOT$.BIN" from on-board flash disk...Done! (size = 12,582,912...
View ArticleRe: SSG140 failed during upgrade
1: I understand that the imagekey.cer is newly downloaded software key. 2: Are you trying to import the same key during the boot loop as well? YOu nned to upload the device image/software not the...
View ArticleRe: SSG140 failed during upgrade
Downloaded latest device software from Juniper website and upload to the device via TFTP, instead of imagekey.cer. Thanks,Vikas
View ArticleRe: SSG140 failed during upgrade
Hi Vikas, tried with ssg140.6.2.0r9.0, ssg140.6.3.0r17.0 and the latest just downloaded ssg140.6.3.0r21.0: Serial Number [0185042014600047]: READ ONLYHW Version Number [1010]: READ ONLYSelf MAC...
View ArticleRe: SSG140 failed during upgrade
You are hitting the sae issue as KB http://kb.juniper.net/InfoCenter/index?page=content&id=KB5280&actp=search , not sure whether your imagekey.cer was loaded correctly or not. 1: Do you have...
View ArticleRe: SSG140 failed during upgrade
Yes, I try the image that was working.The link that you attached is for NS, I don't know if it works with SSG or not.During the boot process , the following messages appear: Juniper Networks SSG-140...
View ArticleRe: SSG140 failed during upgrade
There could be two things, you can do: 1: The 6.2.0r9 version(signed by old key) might be corrupted, you can contact JTAC if you need this version for recovery.2: Try upgrading boot loader and then...
View Article