Re: Basic configuration for juniper SSG140
the Ucopia device connected to two AP and will act as DHCP server that will manage the users and will rout the trafic to the firewall on F0/0 (10.145.214.13/29) then the firewall will route all the...
View ArticleRe: Basic configuration for juniper SSG140
Hello, You can put fe0/0 in trust zone & fe0/2 in untrust zone.Have a security policy from trust to untrust zone allowing desired internet access. If NAT is configured on ISP router, your work is...
View ArticleRe: Basic configuration for juniper SSG140
For the connection i have connect as you suggest but the Routing is the issue. i can ping the Ip that connected to Fe0/0 and that connected to fe0/2.It's first time to configure firewall so i don't...
View Articlecannnot connect to webui using any browser
have an SSG 520 running Screen OS 6.2. I used to be able to connect to it via webui, but now, no matter which browser I use, I cannot connect. For firefox, I get "Error code:...
View ArticleRe: cannnot connect to webui using any browser
Hello, I think the cause of the problem is here: SSL: cipher RC4-MD5SSL: cipher RC2-CBC-MD5SSL: cipher IDEA-CBC-MD5SSL: cipher RC4-MD5ssl3_get_client_hello() failed, no shared cipher Firefox or Chrome...
View ArticleRe: cannnot connect to webui using any browser
the only other option is to use very old browsers. I end up using an old version of IE to manage these devices. In 6.3 you are able to change the cipher to 3DES SHA1 and allow the connections. Not...
View ArticleRe: cannnot connect to webui using any browser
changing it to "3des sha-1" did the trick. Thanks guys, appreciate it
View Articlecan't fetch reports for netscreen firewall
Hi, Suddenly data related to cpu/memory/session/temp related to netscreen firewall is stopped recording in MPBN report.The server IP is well reachable.Community strings and versions are same on...
View ArticleRe: How I can make BGP configuration on SSG-140
Where i need to add the below information which ISP has been sent me: 1) Vlan 1111 - International Traffic Communication network: 145.148.140.120/29 International Router1, ASN57344, 145.148.140.121/29...
View ArticleRe: can't fetch reports for netscreen firewall
There is not an equivelent command on ScreenOS. You would need to do a MIB walk from an external address. I would recommend running a debug snmp all to see what is happening. Also, have you recently...
View ArticleSSG-350 Sessions Table and New SRX
Hello and thank you in advanced for any advice. Our current setup is a /30 WAN and a /25 LAN handoff from the ISP. Our device is the SSG-350 and have configured the /30 for external and the /25...
View ArticleRe: SSG-350 Sessions Table and New SRX
There is not a way to turn off the statefull aspect of the firewall.
View ArticleRe: SSG-350 Sessions Table and New SRX
Just as I thought and as it should. Thanks so much.
View ArticleRe: How I can make BGP configuration on SSG-140
Example for the one peer. Assign the 145.148.140.121 address to ethernet 0/2 Add the BGP to the VR and set the neighborsset vr untrust protocol bgp 57344 set vr untrust-vr protocol bgp enable set...
View ArticleRe: can't fetch reports for netscreen firewall
Hi, There is no upgrade done.How to check if mib file is present on the node or not? BR//Swati
View ArticleRe: can't fetch reports for netscreen firewall
- The MIB files are firmware specific and will be the same for all the ScreenOS devices.- You can download the MIB files at the link https://www.juniper.net/techpubs/software/screenos/mibs.html....
View ArticleSSG5 ScreenOS update failed (unit continuously reboots)
I have an SSG-5-SH that was running ScreenOS firmware version 6.1.0r2.0. Everything else was working but I wasn't able to see the menu on the left side of the screen using WebUI so I thought I would...
View ArticleRe: SSG5 ScreenOS update failed (unit continuously reboots)
If you have an account with JTAC you can request no longer posted versions of ScreenOS. But with the update of the key you probably won't be able to boot the old versions now either. Do you get the...
View ArticleRe: can't fetch reports for netscreen firewall
Thanks for sharing the MIB file.Can you confirm how to check if MIB file is present in the node?Is there any command to check the same?
View ArticleRe: can't fetch reports for netscreen firewall
Also share the MIB for session and temperature. Thanks in advance
View Article