Re: NetScreen 5400 problem
These are generally hardware failure errors. But you can try to schedule a reboot and see if the message clears.
View ArticleRe: SSG5 Bandwith problems
The issue will not be the firmware but you can get newer versons from the support download area once you get your account setup and support contract linked. To troubleshoot bandwidth issues I would...
View ArticleRe: cannot download config file from GUI after upgrade
Hi, i cant pull the file via cli, when i do get config i get an error "the configuration is exceeding the size restriction"
View ArticleRe: MIP VPN
One tiny additional question: tunnel.1, tunnel.2 and loopback.1 are in the DMZ zonebgroup0 is in the Trust zone Two policies allow traffic from Trust to DMZ and vice versa. I was able to ping from my...
View ArticleJuniper SSG550 dual wan default route issue
Hi,everybody.I have a issue with two default route on SSG FW.HQ have a Juniper SSG550 and E0/1 public IP address 1.1.1.1/24 in Untrust Zone，E0/2 public IP address 2.2.2.2/24 in Untrust Zone. There have...
View ArticleRe: cannot download config file from GUI after upgrade
And are you able to get the output of both commands:get sys-cfg | incl configget config | incl size If yes, please share it
View ArticleRe: Juniper SSG550 dual wan default route issue
Hello, Can you provide the output from SSG550 of command: 'get flow' Regards, Rushi
View ArticleMany - to - One NAT
Dears,, Can I nat MANY private IPs into One public IP, in my case i need to nat the below Private IPs192.168.1.10/32172.31.15.10/3210.10.10.10/32 Public IP8.x.x.x/32 thanks in advance...
View ArticleRe: Many - to - One NAT
Hi, http://www.juniper.net/techpubs/software/screenos/screenos6.3.0/630_ce_AddressTranslation.pdf I doubt that you can host multiple distinct private IPs behind one single IP. even if they are in the...
View ArticleClik here to view.
Re: SSG5 Bandwith problems
Thanks for the replay , I've checked the interfaces they are on full duplex both , bgroup has 0 on Egress and Ingress so no limit there alsow I checked in Policies: from trust to untrust has no...
View ArticleRe: SSG5 Bandwith problems
I understand that you never got revised bandwidth whether it's old or new firmware. The bandwidth also depends on the number of users using the network resources at the same time. Have you tried...
View ArticleRe: SSG5 Bandwith problems
I have tried 2 things :1) Without firewall just my ssg5 ping still was 152) I pluged a laptop directly to ISP cable pass the firewall and ssg5 and then it was 40 more or less So the fault is buried in...
View ArticleRe: cannot download config file from GUI after upgrade
It seems to be a knows issue and the earlier requested command outputs will help to confirm it. You will need to reduce the config file size by removing the unnecessary configuration or by configuring...
View ArticleRe: Many - to - One NAT
Create a DIP on the public interface for the 8.x.x.x/32, then create a policy for the addresses you want to use this address and select to nat-dst with that DIP.
View ArticleRe: cannot download config file from GUI after upgrade
Hi A'bed, no i cant get the output of get config, it gives me error message "the configuration is exceeding the size restriction"
View ArticleRe: cannot download config file from GUI after upgrade
Hi Vikas, just a question from the steps on the link that you provide, since we cannot download the current config, the config that we are going to upload is the old config that we back up before? if...
View ArticleRe: cannot download config file from GUI after upgrade
Hi, 1: The current config file will have config till last successful save.2: I meant to try removing the unnecessary config from the GUI/CLI this will decrease the config file. Or else export the...
View ArticleRe: SSG5 Bandwith problems
Hello, Which tool you are using for tests?Is there any PBR configured on SSG that could probably result in packet drop when tool sends test traffic on multiple ports? Regards, Rushi
View ArticleRe: Many - to - One NAT
thanks for your reply, once i tried to do DIP on the same interface ip address, i recieve and error (invalid DIP parameter), can you find which parameter should be changed to get this done?
View ArticleRe: Many - to - One NAT
Dear, thanks for your reply, actually i didnt get the point here, though i will be checking the pdf document and reply if any further information needed. thanks alot.
View Article