SSG-140 boot loop problem
The firewall is stuck in a boot loop. When I use the serial console I can get the chance to "hit any key to run loader" When I do that and enter the bootloader file and the ip addresses of the tftp...
View ArticleRe: after update boot loader to 1.3.3 ssg5 boots in circle...
I know this is an old thread, but my ssg-140 has the same problem, the boot llop, but when I enter the file name, ip address of the tftp server it times out before the image is loaded! any help...
View ArticleRe: SSG-140 boot loop problem
r!r!r! indicates that the firewall is not able to reach the TFTP server. Do you have the TFTP server connected to eth0/0?
View ArticleRe: Traffic Shaping SSG
You can use maximum bandwidth to control this. You would need to specify the speeds on the egress interface, then you would need to set maximum bandwidth in the policy.
View ArticleRe: after update boot loader to 1.3.3 ssg5 boots in circle...
I would give it a try with a different TFTP server software. I had issues using one software (Pumpkin I think) but then it worked successfully with another (Solarwinds I think).
View ArticleRe: SSG-140 boot loop problem
Can you confirm you can ping the address you assigned the firewall on the PC? Is the PC firewall turned off? Also it might be the TFTP software compatibility. I once had a device refused to load with...
View ArticleSSG5 - moving from 10M to 100M line
All, We currently have a 10M line as out main line and an ADSL backup line on an SSG5 F/W 6.3.0r16.0 and H/W 710(0).We just got connected to a 100M line and i've basically configured the 100M line on...
View ArticleRe: SSG5 - moving from 10M to 100M line
Only one default route will be active by default. You could do some PBR, or configure more specific routes for the traffic that you move over.
View ArticleRe: SSG5 - moving from 10M to 100M line
Your other option is to place the 100m service interface into the second virtual router. Then put your default route for this server here. You will then need a routes between the VR for anything that...
View ArticleHow to use public IPv4 IPs inside VPN tunnels for several customers
Hi firewall folks, what we are trying to achieve is sth. similar like this. Let's say you have X customers. Each Customer needs to access the same servers in the datacenter. Since we have a unused IPv4...
View ArticleRe: How to use public IPv4 IPs inside VPN tunnels for several customers
If you have a one-to-one relationship of the public ip to servers, then the simplest configuration would be to create a MIP on your tunnel interface mapping the public ip to the private one. This will...
View ArticleRe: How to use public IPv4 IPs inside VPN tunnels for several customers
Thanks Steve, ok but I have to bind several vpns to the same tunnel interface. I know this is possible however how does the traffic to the customers flow (reverse direction). I guess I have to use...
View ArticleRe: SSG5 - moving from 10M to 100M line
Thanks - would i better off just updating the existing 10M connection with that of the 100M ones? I though it would be easier adding the 100M line as an additional connection but it sounds as though...
View ArticleRe: How to use public IPv4 IPs inside VPN tunnels for several customers
you are correct, for multiple tunnels bound to the same interface then NHTB entries must be made to direct the remote side traffic into the correct tunnel. These can be automatically created if you are...
View ArticleRe: SSG5 - moving from 10M to 100M line
Yes, you can only have one default route active per router at a time.
View ArticleRe: HELP THE NOOB
Steve, I just found your videos on YouTube. I am on the third one. We have two of the ScreenOS ones we are trying to deal with....ugh... Thank you for your guidance!Kirk
View ArticleRe: Swapping primary/secondary ISP
Thanks for the advice a few months ago.. I set it up, but now I have a question. I have not tested the failover yet, but my backup (0/0) shows down in the interface list... I've attached a pic of it.....
View ArticleRe: Swapping primary/secondary ISP
If you have configured it as a backup interface, it will remain down until the active link goes down.
View Articlehow much space use for Log on ssg20 128MB
hai all, i have ssg20 128MB, the question from my customer "how much space use for log on SSG20 seri 128MB". Thanks,
View ArticleRe: how much space use for Log on ssg20 128MB
Hi, SSG using compact flash for logsAnd when its full , it starts to overwrite the old logs.
View Article
