SSG-5-SH not working anymore
When I connect the console I get the following :uniper Networks SSG5 Boot Loader Version 1.3.2 (Checksum: A1EAB858) Copyright (c)...
View ArticleRe: SSG-5-SH not working anymore
Hello, Have TFTP server with latest SSG5 OS directly connected to lowest port on SSG5.Reboot the device and when prompted 'Hit any key to run loader' enter any key and follow the below KB article:...
View ArticleRe: how much space use for Log on ssg20 128MB
Hello, You can also check this link. http://kb.juniper.net/InfoCenter/index?page=content&id=KB4258&actp=search Regards, Rushi
View ArticleRe: SSG-5-SH not working anymore
Hi,Thanks for your answer,I will try this on friday , before I will not have time. So I put the Screen OS on the TFTP server .TFTP server connecting to the lowest port ? you mean 0/2 ? If it does not...
View ArticleRe: SSG-5-SH not working anymore
Hi, This does not look like the DHCP issue. DHCP problem will cause a reboot/crash loop. But in your case, the device is stuck during bootup.Please try reinstalling the firmware and bootloader as Rushi...
View ArticleRe: SSG-5-SH not working anymore
Hi, @mr Gokul : I meant my 2nd Juniper : it is in a loop , but I try to fix first my 1st Juniper. So on this first one :I followed both documents :Upgraded bootloader,load Screen Os :but on loading...
View ArticleSSG-5-SH Loops
SSG-5-sh loops all the time in startup,What can I do ?I already upgrdade Bootloader and Screen OS but it does not help
View ArticleRe: SSG-5-SH not working anymore
I retried to put another SCREEN OS on it. that was succesful , but when I boot the SSG5 it still stops like before . Is there something else I could do ?
View ArticleRe: SSG-5-SH Loops
If you upgrade ScreenOS Version from lower 6.3 to 6.3.x you must deactivate DHCP-Server. When the DHCP-Server is activated at booting the SSG boot process loops. If you can't deactivate the DHCP Server...
View ArticleRe: SSG-5-SH Loops
Hi,Thank you for your answer. Deactivating before upgrade is not possible anymore. But you speak about putting the command for deactivating DHCPbut where ?I do not see where I can log in ?
View ArticleRe: SSG-5-SH Loops
Please open a case with JTAC for assistance. It might be a different issue than with the DHCP server.
View ArticleSSG-5-SH no reaction
HI,I have problems with 3 SSG-5-SH for this moment.I have already 2 topics open on the other 2 SSG-5-SH. NOw here my 3rd one.I bought it on eBay because I wanted to have a spare SSG-5-SH.When I put...
View ArticleRe: SSG-5-SH Loops
I would like to try first the DHCP solution , but I do not understand how to do
View ArticleRe: SSG-5-SH no reaction
Most of the time when I put power on it :everything is blinking :power + status orange ,eth0/0 thru eth 0/6 green. After a while only power + status are solid green. the rest are out.
View Articletcp-syn-check
Hello, Have a weird one here. We have an ISG2000 HA pair that we have tools behind it that manage devices all over the country. We have enabled tcp-syn-check on it. Since then. We have a found devices...
View ArticleRe: tcp-syn-check
Do you have SYN-CHECK or SYN-BIT-CHECK? SYN-CHECK is done in the CPU, so it should not matter if it is set to no-hw-sess.
View ArticleRe: tcp-syn-check
Hi. thanks for the response... here is the setup. firewall(M)-> get conf | i tcp-syset flow tcp-syn-checkunset flow tcp-syn-bit-check and the policy has = hardware session: off thanks.
View ArticleRe: SSG-5-SH not working anymore
The Device is working now. Special Thanks to Mr. Ralf Zimmermann
View Article