Re: Problem with VPN configuration: The peer sent a TS that did not match the...
H Matthias, Please check KB https://kb.juniper.net/InfoCenter/index?page=content&id=KB5049&actp=search for the event logs. Do you see the same error for this VPN? If yes, then please configure...
View ArticleRe: Problem with VPN configuration: The peer sent a TS that did not match the...
Hi Vikas, Thanks a lot for your help. IKE policy checking was already disabled in my case. But it turned out it was... a Policy problem!I didn't had proper policy from untrust to trust with tunnel. Now...
View ArticleHow to access ns5gt juniper firewall externally
I have a internal lan network setup connected to cyberoam firewall cr300i . I want to configure another firewall juniper ns5gt so that i can access it from outside using external public ip . The...
View ArticleRe: How to access ns5gt juniper firewall externally
Just a preface that it is generally NOT a good idea to allow mgmt port access to the internet. If you do need to do this then you should set ip address restrictions so that only trusted subnets can...
View ArticleMisleading logging on ScreenOS ISG1000 FW
Hi ,i have a very strange issue with My logging options :here is the scenario :i have IP address on the A Zone 1.1.1.1 and a nother IP 2.2.2.2 on Zone Bi have created Policy to permit access from...
View ArticleSSG-140-SB and SSG-140-SH Cluster Compatibility
Hi there I'm hopeing someone might be able to advise. I have a SSG-140-SB that I want to set up in a cluster with another SSG-140 that I an waiting to recieve in the mail. I do not know if the SSG140 I...
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
They are compatible, however, you might have to reduce the max sessions on the 512 model.
View ArticleNetScreen 5400 problem
Hello everyone,I have a NetScreen 5400 with M2 management module. At the login via the CLI appears the following message: "PCI Master Data parity error on Req queue read". I can login and execute...
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
Many thanks for the quick response rseibert. Would I be required to manually set the max sessions possible on the 512 model?
View ArticleQoS configuration based on destination ip in ssg 5
Dear Sir/Madam,please let me know how to configure QoS configuration based on destination ip in ssg 5. thanks in advance.
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
Those are limites based on the hardware not a configurable parameter. I would just setup so that the lower value hardware is the primary device in the active/passive cluster. That way the lower values...
View ArticleRe: QoS configuration based on destination ip in ssg 5
You would create a policy for the desired traffic you want this classification to apply to. Then add the desired parameters to the policy. See the details in chapter 7 in the fundamentals volume here....
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
Very good advice. Thank you so much for your help.
View ArticleRe: NetScreen 5400 problem
Sounds like a hardware problem. I would recommend opening a JTAC ticket to see about an RMA.
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
spuluka wrote:Those are limites based on the hardware not a configurable parameter. I would just setup so that the lower value hardware is the primary device in the active/passive cluster. That way...
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
Thank you ver much for your input, it's appreciated. Should I then indeed set a session limit on bothe devices? Sorry to keep troubling you.
View ArticleRe: SSG-140-SB and SSG-140-SH Cluster Compatibility
Setting the session limit would make sense. Use this command to see the current max limit on both devices get session info Take the LOWER max limit and then set the HIGHER device to the LOWER limitset...
View ArticleNetScreen 5400 problem: PCI parity error. HELP!
Hello everyone,I have a NetScreen 5400 with M2 management module. At the login via the CLI appears the following message: "PCI Master Data parity error on Req queue read". I can login and execute...
View ArticleRe: NetScreen 5400 problem
Sounds like a hardware problem. I would recommend opening a JTAC ticket to see about an RMA.
View Article